基于目视间隔条件下的碰撞风险分析

为研究目视间隔条件下进近过程中前后两飞机的碰撞风险问题,通过Reich碰撞模型和碰撞风险模型,引入目视误差作为影响因素之一,建立基于目视间隔条件下的风险评估模型.从纵向、横向、垂向三个维度分析前后两飞机碰撞的概率,求得目视条件下进近两机碰撞的概率,以此作为风险分析的结果.计算结果表明,利用模型计算出的碰撞风险符合国际民航组织规定的航空器空中碰撞概率规定值.故而可证明,目视间隔和目视进近可作为一种安全的空中交通管制运行模式缩小安全间距,提高空域利用率,增加飞行流量.     

Flow separation control on swept wing with nanosecond pulse driven DBD plasma actuators

A 15° swept wing with dielectric barrier discharge plasma actuator is designed.Experimental study of flow separation control with nanosecond pulsed plasma actuation is performed at flow velocity up to 40 m/s. The effects of the actuation frequency and voltage on the aerodynamic performance of the swept wing are evaluated by the balanced force and pressure measurements in the wind tunnel. At last, the performances on separation flow control of the three types of actuators with plane and saw-toothed exposed electrodes are compared. The optimal actuation frequency for the flow separation control on the swept wing is detected, namely the reduced frequency is 0.775, which is different from 2-D airfoil separation control. There exists a threshold voltage for the low swept wing flow control. Before the threshold voltage, as the actuation voltage increases, the control effects become better. The maximum lift is increased by 23.1% with the drag decreased by 22.4% at 14°, compared with the base line. However, the best effects are obtained on actuator with plane exposed electrode in the low-speed experiment and the abilities of saw-toothed actuators are expected to be verified under high-speed conditions.     

In-orbit assessment of laser retro-reflector efficiency onboard high orbiting satellites

The navigation and geodetic satellites that orbit the Earth at altitudes of approximately 20,000 km are tracked routinely by many of the Satellite Laser Ranging (SLR) stations of the International Laser Ranging Service (ILRS). In order to meet increasing demands on SLR stations for daytime and nighttime observations, any new mission needs to ensure a strong return signal so that the target is easily acquirable. The ILRS has therefore set a minimum effective cross-section of 100 million square metres for the on-board laser retro-reflector arrays (LRAs) and further recommends the use of ‘uncoated’ cubes in the arrays. Given the large number of GNSS satellites that are currently supported by SLR, it is informative to make an assessment of the relative efficiencies of the various LRAs employed. This paper uses the laser ranging observations themselves to deduce and then compare the efficiencies of the LRAs on the COMPASS-M1 navigation satellite, two satellites from the GPS and three from the GLONASS constellations, the two GIOVE test satellites from the upcoming Galileo constellation, the two Etalon geodetic spheres and the geosynchronous communications test satellite, ETS-8. All the LRAs on this set of satellites employ back-coated retro-reflector cubes, except those on the COMPASS-M1 and ETS-8 vehicles which are uncoated. A measure of return signal strength, and thus of LRA-efficiency, is calculated using the laser-range full-rate data archive from 2007 to 2010, scaled to remove the effects of variations in satellite range, atmospheric attenuation and retro-reflector target total surface area. Observations from five SLR stations are used in this study; they are Herstmonceux (UK), Yarragadee (Australia), Monument Peak and McDonald (USA) and Wettzell (Germany). Careful consideration is given to the treatment of the observations from each station in order to take account of local working practices and system upgrades. The results show that the uncoated retro-reflector cubes offer significant improvements in efficiency.     

红外成像设备输出图像十字线毛刺或扭曲故障问题技术归零研究

针对某型直升机红外成像设备输出图像十字线毛刺或扭曲问题,在视频处理电路原理分析的基础上,结合不同技术状态的电路板对比分析试验,进行故障排查定位,揭示了故障隐含于锁相电路和电路点像素时钟被干扰的真实原因,给出了消除毛刺或扭曲的解决办法和措施。     

月球取样返回器分离阻力分析与地面分离试验验证

探月工程三期研制的月球取样返回器与轨道器间采用导向装配方式,装配后存在一定预应力,同时在轨两器分离时受空间环境作用而出现热变形,引起的分离阻力会对两器的正常分离产生影响。文章对返回器与轨道器的分离阻力进行分析和测量,并开展相关地面分离验证试验,结果表明,在轨环境引起的分离阻力约为366 N,地面装配应力引起的分离阻力约为160 N,两器分离速度约为0.24 m/s。研究结果可为轨返两器的分离设计提供参考。     

不同雷诺数下翼型气动特性及层流分离现象演化

低雷诺数下空气黏性效应突出,翼型表面普遍存在层流分离现象,相比常规雷诺数情况气动特性显著恶化。采用带预处理的Roe方法求解非定常可压缩Navier-Stokes方程的数值模拟技术和低雷诺数低湍流度风洞油流显示试验技术,对FX63-137翼型不同雷诺数下气动特性和流动结构展开深入研究。通过风洞油流显示试验可以清晰获得低雷诺数层流分离流动的两道油流汇集线。数值模拟结果表明其分别为时均化主分离线和二次分离线,两种结果定性定量均吻合较好,证明了本文的研究方法有效可靠;雷诺数从500 000降至20 000,翼型气动特性和层流分离流动结构均发生显著的变化,伴随阻力系数剧增和升力系数剧降,时均化流动结构从附体至出现经典的长层流分离泡,并最终演化为后缘层流分离泡,相应的两种分离泡的非定常流动结构也存在显著差异;对于阻力系数和升力系数而言,存在不同的临界雷诺数,因为导致阻力系数剧增的机理在于经典长层流分离泡的产生使翼型压差阻力大增,而造成升力系数剧降的主要原因在于后缘层流分离泡使得等效翼型后部弯度减小;非定常结果显示正是由于翼型表面漩涡周期性的生成与脱落,才造成了低雷诺数下升力系数的周期性波动。翼型上表面主分离涡即将脱落时,流线在后缘附近再附,升力系数达到峰值;而当流体从下表面向上卷起二次分离涡时,尾部流线大尺度分离,升力系数降至谷值。     

频域盲源分离的非圆信号推广

作为盲源分离（BSS）问题的最有效解决方法之一,独立分量分析（ICA）算法可以分为时域和频域算法两类.将时域盲源分离的快速算法推广到频域,通过在频域中应用非圆信号的伪协方差矩阵,推导出一个新的固定点算法来解决线性瞬时混合的非圆信号盲源分离（BNSS）问题.仿真实验验证了该算法的有效性.     

多孔介质隔热材料中的辐射热传递分析

新型的多孔材料以其重量轻、强度高备受航天工程设计人员的亲睐,尤其是作为隔热材料使用,可以说是航天工程热防护系统的热门材料.多孔介质在辐射热传递方面具有吸收发射和散射的功能,这些功能在其接受外来热流的作用下,于内部达到热能量平衡,求解这一平衡方程就可以求出辐射热流在材料中的分布.由于求解这一方程的困难,许多学者对材料特性...     

利用流线法决定绕扁长椭球流动分离的位置

本文按照流线法把所测量的扁长椭球的压力分布用于决定涡层型三维流动分离,按边界层边缘处流线会聚的位置近似地决定分离线的位置。作为算例,计算了扁长椭球体在α=30°状态下的绕流,并在水洞中作了流场显示,数值结果和实验结果的对比表明,二者十分一致。分析表明,涡层型分离不仅与壁面极限流线的收敛有关,而且还与边界层边缘处流线会聚有关,前者的出现并不是引起涡层型流动分离的充要条件。     

一种特殊梯度分布的功能梯度矩形板弯曲问题解析解

研究了一种特殊梯度分布功能梯度材料矩形板弯曲问题。假设材料的弹性模量在板厚度方向上呈幂函数分布,泊松比为常数,引入PLEVAKO解,利用分离变量法,导出四边简支功能梯度材料矩形板弯曲问题的解析解。通过算例分析了材料组分变化时,功能梯度板应力和位移的变化规律。结果显示不同梯度分布板结构中的应力、位移的变化规律是不同的,有时甚至差别很大。该方法为发展针对功能梯度材料特点的数值算法和简化理论提供依据。